We have addressed the question of the suitability of the vane‐in‐cup as a rheometer geometry. A numerical simulation of this geometry was conducted for a power‐law fluid and the results compared with a similar study for a conventional bob‐in‐cup geometry. The comparison indicates that for a sufficiently shear‐thinning fluid (of shear‐thinning index less than 0.5) the fluid within the periphery of the vane blades is essentially trapped there and turns with the vane as a solid body. Calculation of the shear stress at the cup wall indicates that this quantity is equal in both geometries for a given rotational rate of the spindle. Thus the torque required to turn the spindle would be the same and identical flow curves would be predicted. This prediction was tested on two fluids thought to possess a yield stress: a 5.5% sodium carboxymethylcellulose (CMC) solution and a 4.2% Veegum PRO clay suspension. Equivalent flow curves were obtained at very low stresses/shear rates but a sudden, catastrophic viscosity loss was found for both fluids with the bob at shear rates which were still quite low. Such a loss was observed with the vane as well, but at much higher shear rates. It is suggested that this phenomenon is a form of apparent slip due to the formation of a thixotropic layer at the bob/vane surface. The much flatter stress profile obtained in the vane geometry is reasoned to postpone the formation of this layer. Rheological data obtained with the vane appear to be a faithful representation of these materials and show the absence of a true yield stress.
Skip Nav Destination
Article navigation
August 1990
Research Article|
August 01 1990
The vane‐in‐cup as a novel rheometer geometry for shear thinning and thixotropic materials
H. A. Barnes;
H. A. Barnes
Unilever Research, Port Sunlight Laboratory, Quarry Road, Bebington, Merseyside L63 3JW, England
Search for other works by this author on:
J. O. Carnali
J. O. Carnali
Unilever Research U. S., 45 River Road, Edgewater, New Jersey 07020
Search for other works by this author on:
J. Rheol. 34, 841–866 (1990)
Article history
Received:
July 21 1989
Accepted:
February 23 1990
Citation
H. A. Barnes, J. O. Carnali; The vane‐in‐cup as a novel rheometer geometry for shear thinning and thixotropic materials. J. Rheol. 1 August 1990; 34 (6): 841–866. https://doi.org/10.1122/1.550103
Download citation file:
Pay-Per-View Access
$40.00
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Citing articles via
Rheo-SINDy: Finding a constitutive model from rheological data for complex fluids using sparse identification for nonlinear dynamics
Takeshi Sato, Souta Miyamoto, et al.
Learning a family of rheological constitutive models using neural operators
Deepak Mangal, Milad Saadat, et al.
Linear viscoelasticity of nanocolloidal suspensions from probe rheology molecular simulations
Dinesh Sundaravadivelu Devarajan, Rajesh Khare
Related Content
The bucket rheometer for shear stress-shear rate measurement of industrial suspensions
J. Rheol. (September 2007)
Numerical investigation of the reduction of wall-slip effects for yield stress fluids in a double concentric cylinder rheometer with slotted rotor
J. Rheol. (November 2010)
Analysis of the vane rheometer using 3D finite element simulation
J. Rheol. (March 2007)
Measurement of foam modulus via a vane rheometer
J. Rheol. (July 1998)
Rheo-PIV of yield-stress fluids in a 3D-printed fractal vane-in-cup geometry
J. Rheol. (June 2023)