In fast neutron reactors, some parts can be submitted to displacements between each other (as movable parts for example). On these parts, the contact areas usually need a hardfacing coating. The standard hardfacing alloy is a cobalt-base alloy (as, for example Stellite®6). Unfortunately, in the primary coolant circuit and on wear conditions, cobalt can be released. Under neutron flux, the 59Co, stable, can be transmuted into 60Co by radioactive capture of neutrons and, therefore, can contaminate the primary circuit. Therefore, it is desired to replace this cobalt based hardfacing alloy by a cobalt-free one.

First we sum up the existing results on cobalt-free hardfacing materials. Several types of materials such as nickel-base alloys, iron-base alloys and ceramics own interesting properties. However, it has been evidenced that there are few and incomplete works that attempt to understand the links between the material composition, the microstructure of the material obtained by the deposition process and its set of parameters, and the tribo-corrosion behavior of the coating.

Consequently, it has been decided to tackle this issue by selecting a set of possible cobalt-free hardfacing materials and using laser cladding. The material selected as first candidate is the Colmonoy® alloy (Colmonoy® 52 for laser cladding). In the industrial application, the alloy will be deposited on the stainless steel.

The following part of the article is dedicated to the presentation of the process parameter search. The cobalt-free hardfacing alloy is provided in powder. It is expected that laser metal deposition can provide a controlled dilution of the substrate, a low deformation and a fine microstructure by a fine control of the energy deposition. In addition, the laser metal deposition process offers a very large range of parameter values.

The experimental setup is presented. The first clads obtained have exhibited porosities, cracks and deformation. The other campaigns of experiments have been focused of avoiding/suppressing these defects by changing the process parameters. In parallel, the evolution of the composition of the clad and its microstructure are analyzed. Hard phases with varying shape and composition, depending on the process parameter, have been evidenced.

Finally, the presentation concludes by summarizing the links between the microstructure of the Colmonoy® 52, the process parameter and a selection of the parameter set for further tribology (pin-on-disk) and corrosion (liquid sodium medium) tests.

1.
P.M.
Dunckley
,
T.F.J.
Quinn
, and
J.
Salter
,
Studies of the Unlubricated Wear of a Commercial Cobalt-base Alloy at Temperatures up to about 400°C
,
ASLE Transactions
,
19
(
3
), (
1976
), pp.
221
231
2.
H.
So
,
C.T.
Chen
, and
Y.A.
Chen
,
Wear Behaviours of Laser-clad Stellite Alloy 6
,
Wear
,
192
(
1-2
), (
1996
), p.
78
84
3.
J.T.M
de Hosson
, and
L.
de Mol van Otterloo
, Surface Engineering with Lasers of Co-base Materials, Surface Treatment, Computer Methods and Experimental Measurements.
Comput. Mech. Publications
,
Southampton, UK
, (
1997
), pp.
341
59
4.
de Mol van Otterloo
,
J.L.
and
J.T.M.
de Hosson
,
Microstructure and abrasive wear of cobalt-based laser coatings
,
Scripta Materialia
,
36
(
2
), (
1997
), pp.
239
45
5.
D.H.E.
Persson
,
S.
Jacobson
,
S.
Hogmark
,
Effect of temperature on friction and galling of laser processed Norem 02 and Stellite 21
,
Wear
255
, (
2003
), pp.
498
503
6.
D. H. E.
Persson
,
Laser processed low friction surfaces
, Dissertation for the degree of Licentiate of Philosophy in Materials, Materials Science Division, the Ångström Laboratory,
Uppsala University
,
Sweden
, March (
2003
)
7.
C. B.
Bahn
,
B. C.
Han
,
J. S.
Bum
,
I. S.
Hwang
,
Chan Bock
Lee
,
Wear performance and activity reduction effect of Co free valves, in PWR environment
,
Nuclear Engineering and Design
231
, (
2004
), pp.
51
65
8.
M.
Corchia
,
P.
Delogu
, &
F.
Nenci
,
Microstructural Aspects Of Wear-Resistant Stellite And Colmonoy Coatings by Laser Processing
,
Wear
, Volume
119
, pp.
137
152
,
1987
9.
Kashani
,
A.
Amadeh
, &
H.
Ghasemi
,
Room and high temperature wear behaviors of nickel and cobalt base weld overlay coatings on hot forging dies
.
Wear
,
262
(
7-8
), pp.
800
806
,
2007
10.
Qian
Ming
,
L.C.
Lim
,
Z.D.
Chen
,
Laser cladding of nickel-based hardfacing alloys
,
Surface and Coatings Technology
106
, (
1998
), pp.
174
182
11.
D.
Kesavan
, &
M.
Kamaraj
,
The Microstructure and High Temperature Wear Performance of a Nickel Base Hardfaced Coating
,
Surface and Coatings Technology
,
204
(
24
), pp.
4034
4043
,
2010
12.
C.
Navas
,
R.
Colaço
,
J.
Damborenea
, &
R.
Vilar
,
Abrasive Wear Behaviour of Laser Clad and Flame Sprayed-Melted NiCrBSi Coatings
,
Surface and Coatings Technology
,
200
(
24
), pp.
6854
6862
,
2006
13.
K.
Komvopoulos
,
K.
Nagarathnam
,
Processing and Characterization of Laser-Cladded Coating Materals
,
J. of Engineering Materials and Technology
, vol.
112
, pp.
131
143
,
1990
This content is only available via PDF.
You do not currently have access to this content.