Laser cutting with multibeam diffraction pattern using an adaptive optics is studied. Infrared (IR) continuous single-mode fiber laser with maximum power of 200 W is applied to laser cutting of thin metal sheets, together with liquid crystal on silicon spatial light modulator (SLM). SLM can be used as the adaptive diffractive optical element, which can modify intensity profile of the laser beam almost arbitrary. In studies single Gaussian laser beam was divided into multiple spots. It was found out that with this way it is possible to enhance the cutting quality and also decrease pressure of the needed assist gas. Multibeam configuration enabled to laser cut burr free with 50% less protection gas pressure compared to single beam laser cutting with conventional optics.
REFERENCES
1.
V. P.
Babenko
and V. P.
Tychinskii
, “Gas-jet laser cutting (Review)
,” Sov. J. Quantum Electron.
2
, 399
–410
(1973
).2.
L. D.
Scintilla
, L.
Tricarico
, A.
Wetzig
, A.
Mahrle
, and E.
Beyer
, “Primary losses in disk and CO2 laser beam inert gas fusion cutting
,” J. Mater. Process. Technol.
211
, 2050
–2061
(2011
).3.
L. D.
Scintilla
and L.
Tricarico
, “Experimental invesigation on fiber and CO2 inert gas fusion cutting of AZ31 magnesium alloy sheets
,” Opt. Laser Technol.
46
, 42
–52
(2013
).4.
D.
Petring
, T.
Molitor
, F.
Schneider
, and N.
Wolf
, “Diagnostics, modeling and simulation: Three keys towards mastering the cutting process with fiber, disk and diode lasers
,” Phys. Proc.
39
, 186
–196
(2012
).5.
C.
Wandera
and V.
Kujanpää
, “Characterization of the melt removal rate in laser cutting of thick-section stainless steel
,” J. Laser Appl.
22
, 62
–70
(2010
).6.
C.
Wandera
, A.
Salminen
, and V.
Kujanpää
, “Inert gas cutting of thick stainless steel and medium-section aluminum using a high power fiber laser
,” J. Laser Appl.
21
, 154
–161
(2009
).7.
L. D.
Scintilla
, L.
Tricarico
, A.
Wetzig
, and E.
Beyer
, “Investigation on disk and CO2 laser beam fusion cutting differences based on power balance equation
,” Int. J. Mach. Tools Manuf.
69
, 30
–37
(2013
).8.
M. H.
Brügmann
and T.
Feurer
, “Comparative theoretical analysis of continuous wave laser cutting of metals at 1 and 10 μm wavelength
,” Appl. Phys. A: Mater. Sci. Process.
(published online).9.
K.
Hirano
and R.
Fabbro
, “Possible explanation for different surface quality in laser cutting with 1 and 10 m beams
,” J. Laser Appl.
24
, 012006
(2012
).10.
C.
Wandera
, A.
Salminen
, F. O.
Olsen
, and V.
Kujanpää
, “Cutting of stainless steel with fiber and disk laser
,” in ICALEO
, Phoenix, AZ
, USA
, 30th October–2nd November (2006
), pp. 211
–220
, Paper No. 404.11.
C.
Wandera
, V.
Kujanpää
, and A.
Salminen
, “Laser power requirement for cutting thick-section steel and effects of processing parameters on mild steel cut quality
,” Proc. Inst. Mech. Eng., Part B
225
, 651
–661
(2011
).12.
R. J.
Beck
, J. P.
Parry
, W. N.
MacPherson
, A.
Waddie
, N. J.
Weston
, J. D.
Shephard
, and D. P.
Hand
, “Application of cooled spatial light modulator for high power nanosecond laser micromachining
,” Opt. Express
18
, 17059
–17065
(2010
).13.
Z.
Kuang
, W.
Perrie
, J.
Leach
, M.
Sharp
, S. P.
Edwardson
, M.
Padgett
, G.
Dearden
, and K. G.
Watkins
, “High throughput diffractive multi-beam femtosecond laser processing using a spatial light modulator
,” Appl. Surf. Sci.
255
, 2284
–2289
(2008
).14.
R. J.
Beck
, A.
Waddie
, J. P.
Parry
, J. D.
Shephard
, M. R.
Taghizadeh
, and D. P.
Hand
, “Adative laser beam shaping for laser marking using spatial light modulator and modified iterative fourier transform algorithm
,” Phys. Proc.
12
, 468
–472
(2010
).15.
Y.
Hayasaki
, T.
Sugimoto
, A.
Takita
, and N.
Nishida
, “Variable holographic femtosecond laser processing by use of a spatial light modulator
,” Appl. Phys. Lett.
87
, 031101
(2005
).16.
M.
Silvennoinen
, J. J. J.
Kaakkunen
, K.
Paivasaari
, and P.
Vahimaa
, “Parallel microtructuring using femtosecond laser and spatial light modulator
,” Phys. Proc.
41
, 693
–697
(2013
).17.
H.
Takahashi
, S.
Hasegawa
, A.
Takita
, and Y.
Hayasaki
, “Sparse-exposure technique in holographic two-photon polymerization
,” Opt. Express
16
, 16592
–16599
(2008
).18.
J. J. J.
Kaakkunen
, I.
Vanttaja
, and P.
Laakso
, “Fast micromachining using spatial light modulator and galvanometer scanner with infrared pulsed nanosecond fiber laser
,” J. Laser Micro/Nanoeng.
9
, 37
–41
(2014
).19.
M.
Silvennoinen
, J. J. J.
Kaakkunen
, K.
Paivasaari
, and P.
Vahimaa
, “Parallel femtosecond laser ablation with individually controlled intensity
,” Opt. Express
22
, 2603
–2608
(2014
).20.
J.
Turunen
and F.
Wyrowski
, Diffractive Optics: Industrial and Commercial Applications
(Academic Verlag
, Berlin
, 1998
).21.
M.
Silvennoinen
, J. J. J.
Kaakkunen
, K.
Paivasaari
, and P.
Vahimaa
, “Water spray assisted ultrashort laser pulse ablation
,” Appl. Surf. Sci.
265
, 865
–869
(2013
).22.
D.
Grewell
and A.
Benatar
, “Diffractive optics as beam-shaping elements for plastics laser welding
,” Opt. Eng.
46
, 118001
(2007
).23.
F. O.
Olsen
, K. S.
Hansen
, and J. S.
Nielsen
, “Multibeam fiber laser cutting
,” J. Laser Appl.
21
, 133
–138
(2009
).24.
S. Z.
Shuja
and B. S.
Yilbas
, “Laser multi-beam heating of moving steel sheet: Thermal stress analysis
,” Opt. Lasers Eng.
51
, 446
–452
(2013
).25.
F.
Wyrowski
and O.
Bryngdahl
, “Iterative Fourier-transform algorithm applied to computer holography
,” J. Opt. Soc. Am. A
5
, 1058
–1065
(1988
).26.
S.
Hasegawa
and Y.
Hayasaki
, “Holographic femtosecond laser processing with multiplexed phase Fresnel lenses display on a liquid crystal spatial light modulator
,” Opt. Rev.
14
, 208
–213
(2007
).27.
S.
Hasegawa
, Y.
Hayasaki
, T.
Sugimoto
, and N.
Nishida
, “Holographic femtosecond laser processing with multiplexed phase Fresnel lenses
,” Opt. Lett.
31
, 1705
–1707
(2006
).28.
M.
Yamaji
, H.
Kawashima
, J.
Suzuki
, and S.
Tanaka
, “Three dimensional micromachining inside a transparent material by single pulse femtosecond laser through a hologram
,” Appl. Phys. Lett.
93
, 041116
(2008
).29.
Z.
Kuang
, W.
Perrie
, D.
Liu
, S.
Edwardson
, J.
Cheng
, G.
Dearden
, and K.
Watkins
, “Diffractive multi-beam surface micro-processing using 10 ps laser pulses
,” Appl. Surf. Sci.
255
, 9040
–9044
(2009
).© 2014 Laser Institute of America.
2014
Laser Institute of America
You do not currently have access to this content.
