This article reports on the structure and mechanical properties of CNx thin films deposited by unbalanced reactive magnetron sputtering of C in N2 discharges. The films were grown on Si(001) substrates kept at temperatures (Ts) between 150 and 600 °C. Depending on Ts, the films contained between 15 and 26 at. % N. X‐ray photoelectron spectroscopy of samples typically showed two peaks in the C 1s core level spectrum (centered at 284.5 and 286.2 eV) and two peaks in the N 1s core level spectrum (centered at 398.4 and 400.3 eV). This indicates that there are two types of C–N bonds where N is bonded to both sp2‐ and sp3‐coordinated C atoms in the as‐deposited films. Transmission electron microscopy showed that the films produced in the temperature range 200≤Ts≤600 °C had a highly textured, turbostraticlike structure with the c axis in the plane of the film. The basal planes in this structure were found to be buckled and bent due to incorporation of N in substitutional sites. By contrast, films produced at Ts=150 °C were generally amorphous, but contained ∼3 nm diamond clusters. The mechanical properties were evaluated in nanoindentation experiments. Load versus deflection curves showed that the 0.3 μm films grown at Ts≥200 °C had very high elastic recoveries with values up to 85% of the total indentation displacement. Analyses of the shapes of the load versus deflection curves, using a modeling approach that takes into account the elastic and plastic properties of both the film and the substrate, indicate that the contact deformation of the CNx films was predominantly elastic and the films’ hardness values were estimated to be in the range 40–60 GPa. The high hardness and elasticity are proposed to be due to the buckling of the graphitic basal planes, resulting in a structure where the sp2‐bonded basal planes are terminated with N bonded to sp3‐hybridized carbon atoms that result in a dense, three dimensional, covalently bonded network.
Skip Nav Destination
Article navigation
January 1996
Research Article|
January 01 1996
Structural and mechanical properties of carbon nitride CNx (0.2⩽x⩽0.35) films Available to Purchase
H. Sjöström;
H. Sjöström
Thin Film Division, Department of Physics, Linköping University, S‐581 83 Linköping, Sweden
Search for other works by this author on:
L. Hultman;
L. Hultman
Thin Film Division, Department of Physics, Linköping University, S‐581 83 Linköping, Sweden
Search for other works by this author on:
J.‐E. Sundgren;
J.‐E. Sundgren
Thin Film Division, Department of Physics, Linköping University, S‐581 83 Linköping, Sweden
Search for other works by this author on:
S. V. Hainsworth;
S. V. Hainsworth
Materials Division, Department of Mechanical, Materials, and Manufacturing Engineering, University of Newcastle upon Tyne, Newcastle upon Tyne NE1 7RU, United Kingdom
Search for other works by this author on:
T. F. Page;
T. F. Page
Materials Division, Department of Mechanical, Materials, and Manufacturing Engineering, University of Newcastle upon Tyne, Newcastle upon Tyne NE1 7RU, United Kingdom
Search for other works by this author on:
G. S. A. M. Theunissen
G. S. A. M. Theunissen
Philips Research, 5656 AA Eindhoven, The Netherlands
Search for other works by this author on:
H. Sjöström
Thin Film Division, Department of Physics, Linköping University, S‐581 83 Linköping, Sweden
L. Hultman
Thin Film Division, Department of Physics, Linköping University, S‐581 83 Linköping, Sweden
J.‐E. Sundgren
Thin Film Division, Department of Physics, Linköping University, S‐581 83 Linköping, Sweden
S. V. Hainsworth
Materials Division, Department of Mechanical, Materials, and Manufacturing Engineering, University of Newcastle upon Tyne, Newcastle upon Tyne NE1 7RU, United Kingdom
T. F. Page
Materials Division, Department of Mechanical, Materials, and Manufacturing Engineering, University of Newcastle upon Tyne, Newcastle upon Tyne NE1 7RU, United Kingdom
G. S. A. M. Theunissen
Philips Research, 5656 AA Eindhoven, The Netherlands
J. Vac. Sci. Technol. A 14, 56–62 (1996)
Article history
Received:
August 01 1995
Accepted:
October 07 1995
Citation
H. Sjöström, L. Hultman, J.‐E. Sundgren, S. V. Hainsworth, T. F. Page, G. S. A. M. Theunissen; Structural and mechanical properties of carbon nitride CNx (0.2⩽x⩽0.35) films. J. Vac. Sci. Technol. A 1 January 1996; 14 (1): 56–62. https://doi.org/10.1116/1.579880
Download citation file:
Pay-Per-View Access
$40.00
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Citing articles via
What more can be done with XPS? Highly informative but underused approaches to XPS data collection and analysis
Donald R. Baer, Merve Taner Camci, et al.
Low-resistivity molybdenum obtained by atomic layer deposition
Kees van der Zouw, Bernhard Y. van der Wel, et al.
Related Content
Reactive magnetron sputter deposited CNx: Effects of N2 pressure and growth temperature on film composition, bonding, and microstructure
J. Vac. Sci. Technol. A (September 1996)
Anisotropies in magnetron sputtered carbon nitride thin films
Appl. Phys. Lett. (April 2001)
Stress development during deposition of CN x thin films
Appl. Phys. Lett. (May 1998)
Role of delocalized nitrogen in determining the local atomic arrangement and mechanical properties of amorphous carbon nitride thin films
J. Vac. Sci. Technol. A (November 2000)
Effect of substrate temperatures on amorphous carbon nitride films prepared by reactive sputtering
J. Vac. Sci. Technol. A (July 2008)