Ti-50.9 mol. %Ni was subjected to high-pressure torsion (HPT) deformation for different number of rotations (N) of 0.25, 0.5, 1, 5, and 10. The structural changes induced by HPT were analyzed using x-ray diffractometer (XRD). The surfaces of the samples before and after cell culture were characterized using x-ray photoelectron spectroscopy (XPS). The biocompatibility of the samples was evaluated based on a colony formation assay, nickel ion release, and protein adsorption behavior. XRD analysis revealed the occurrence of grain refinement, phase transformation, and amorphization in the TiNi samples by HPT deformation due to high dislocation density. The changes in chemical composition and thickness of the passive film formed on the surface observed in XPS analysis reveals improvement in the stability of the passive film by HPT deformation. The microstructural change due to the deformation was found to influence the biocompatibility behaviors of TiNi. Plating efficiency and protein adsorption were found to be higher when the samples are in stress-induced martensitic or amorphous state. HPT deformation was found to alter the surface behavior of the TiNi, which effectively reduced the Ni ion release and improved its biocompatibility.
Skip Nav Destination
,
,
Article navigation
June 2014
Research Article|
March 06 2014
Effect of high-pressure torsion deformation on surface properties and biocompatibility of Ti-50.9 mol. %Ni alloys
Dayangku Noorfazidah Awang Shri;
Dayangku Noorfazidah Awang Shri
Graduate School of Pure and Applied Sciences, University of Tsukuba
, Tsukuba, Ibaraki 305-8577, Japan and Structural Materials Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
Search for other works by this author on:
Koichi Tsuchiya;
Koichi Tsuchiya
a)
Graduate School of Pure and Applied Sciences, University of Tsukuba
, Tsukuba, Ibaraki 305-8577, Japan and Structural Materials Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
Search for other works by this author on:
Akiko Yamamoto
Akiko Yamamoto
Biomaterials Unit, International Center for Material Nanoarchitectonics (WPI-MANA), National Institute for Materials Science
, Namiki 1-1, Tsukuba, Ibaraki 305-0044, Japan
Search for other works by this author on:
Dayangku Noorfazidah Awang Shri
Koichi Tsuchiya
a)
Akiko Yamamoto
Graduate School of Pure and Applied Sciences, University of Tsukuba
, Tsukuba, Ibaraki 305-8577, Japan and Structural Materials Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
a)
Electronic mail: [email protected]
Biointerphases 9, 029007 (2014)
Article history
Received:
December 30 2013
Accepted:
February 21 2014
Citation
Dayangku Noorfazidah Awang Shri, Koichi Tsuchiya, Akiko Yamamoto; Effect of high-pressure torsion deformation on surface properties and biocompatibility of Ti-50.9 mol. %Ni alloys. Biointerphases 1 June 2014; 9 (2): 029007. https://doi.org/10.1116/1.4867402
Download citation file:
Pay-Per-View Access
$40.00
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Citing articles via
Drug-eluting contact lenses: Progress, challenges, and prospects
Dongdong Gao, Chunxiao Yan, et al.
Enhancing epithelial tissue sealing of titanium alloy implants through CaCl2-based hydrothermal treatment
Yasushige Sakamoto, Akihiro Furuhashi, et al.
Related Content
Corrosion behavior of HPT-deformed TiNi alloys in cell culture medium
AIP Conf. Proc. (September 2017)
Enhancing biocompatibility, mechanical properties, and corrosion resistance of laser cladding β-TiNb coatings
J. Vac. Sci. Technol. A (September 2023)
Titanium nanostructural surface processing for improved biocompatibility
Appl. Phys. Lett. (October 2006)
Preparation and characterization of hydroxyapatite filled HDPE biocompatible composites for biosensor applications
AIP Conf. Proc. (December 2023)
Enhanced biocompatibility for plasmid DNA on patterned TiO 2 surfaces
Appl. Phys. Lett. (August 2013)