A finite-element analysis is used to explore the impact of elastic material properties, boundary conditions, and geometry, including coiling, on the spatial characteristics of the compliance of the unloaded basilar membrane (BM). It is assumed that the arcuate zone is isotropic and the pectinate zone orthotropic, and that the radial component of the effective Young’s modulus in the pectinate zone decreases exponentially with distance from base to apex. The results concur with tonotopic characteristics of compliance and neural data. Moreover, whereas the maximum compliance in a radial profile is located close to the boundary between the two zones in the basal region, it shifts to the midpoint of the pectinate zone for the apical BM; the width of the profile also expands. This shift begins near the 1 kHz characteristic place for guinea pig and the 2.4 kHz place for gerbil. Shift and expansion are not observed for linear rather than exponential decrease of the radial component of Young’s modulus. This spatial change of the compliance profile leads to the prediction that mechanical excitation in the apical region of the organ of Corti is different to that in the basal region.
Skip Nav Destination
,
,
Article navigation
May 12 2010
Compliance profiles derived from a three-dimensional finite-element model of the basilar membrane
Mario Fleischer;
Mario Fleischer
a)
Faculty of Mechanical Engineering, Institute of Solid Mechanics,
Technische Universität Dresden
, 01062 Dresden, Germany
Search for other works by this author on:
Rolf Schmidt;
Rolf Schmidt
Faculty of Mechanical Engineering, Institute of Solid Mechanics,
Technische Universität Dresden
, 01062 Dresden, Germany
Search for other works by this author on:
Anthony W. Gummer
Anthony W. Gummer
b)
Faculty of Medicine, Section of Physiological Acoustics and Communication,
Eberhard Karls University Tübingen
, Elfriede-Aulhorn-Straße 5, 72076 Tübingen, Germany
Search for other works by this author on:
Mario Fleischer
a)
Rolf Schmidt
Anthony W. Gummer
b)
Faculty of Mechanical Engineering, Institute of Solid Mechanics,
Technische Universität Dresden
, 01062 Dresden, Germanya)
Present address: Department of Otorhinolaryngology, Faculty of Medicine, Technische Universität Dresden, 01062 Dresden, Germany.
b)
Author to whom correspondence should be addressed. Electronic mail: [email protected]
J. Acoust. Soc. Am. 127, 2973–2991 (2010)
Article history
Received:
October 16 2009
Accepted:
March 04 2010
Citation
Mario Fleischer, Rolf Schmidt, Anthony W. Gummer; Compliance profiles derived from a three-dimensional finite-element model of the basilar membrane. J. Acoust. Soc. Am. 1 May 2010; 127 (5): 2973–2991. https://doi.org/10.1121/1.3372752
Download citation file:
Pay-Per-View Access
$40.00
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Citing articles via
A survey of sound source localization with deep learning methods
Pierre-Amaury Grumiaux, Srđan Kitić, et al.
I can't hear you without my glasses
Tessa Bent
Related Content
The pectinate zone is stiff and the arcuate zone determines passive basilar membrane mechanics in the gerbil
AIP Conf. Proc. (May 2018)
Realistic mechanical tuning in a micromechanical cochlear model
J. Acoust. Soc. Am. (July 1989)
Mapping the cochlear partition’s stiffness to its cellular architecture
J. Acoust. Soc. Am. (January 1994)
Sharp mechanical tuning in a cochlear model without negative damping
J. Acoust. Soc. Am. (April 1988)
Biomechanical modeling of reconstructive intervention on the thoracolumbar transition
AIP Conf. Proc. (May 2018)