The present work shows an electrical ammeter for laboratory purpose based on a magnetoresistive (MR) spin-valve (SV) sensor. The proposed ammeter measures a 10 A maximum current and offers a maximum frequency response between 150 and 800 kHz depending on the electronics whole gain. These features are due to the use of a new generation MR-SV current sensor and a conditioning electronics that compensates in frequency and temperature the sensor response. With little adjustments in the electronics and changing the position of the sensor with respect to current carrying conductor, the designed instrument is able to measure higher current levels. The work shows the proposed ammeter with its different subsystems and describes the procedure used to test the instrument. Also a discussion of the obtained experimental results is included.
Skip Nav Destination
Article navigation
October 2012
Research Article|
October 22 2012
Electrical ammeter based on spin-valve sensor
J. Sánchez;
J. Sánchez
1Department of Electronic Engineering,
University of Valencia
, Avda. de la Universitat, s/n, 46100-Burjassot, Spain
Search for other works by this author on:
D. Ramírez;
D. Ramírez
1Department of Electronic Engineering,
University of Valencia
, Avda. de la Universitat, s/n, 46100-Burjassot, Spain
Search for other works by this author on:
J. Amaral;
J. Amaral
2
Instituto de Sistemas e Computadores-Microsistemas e Nanotecnologias (INESC-MN)
, Rua Alves Redol, 9, 1000-029 Lisbon, Portugal
3
Instituto Superior Técnico (IST)
, Av. Rovisco Pais, 1000-029 Lisbon, Portugal
Search for other works by this author on:
S. Cardoso;
S. Cardoso
2
Instituto de Sistemas e Computadores-Microsistemas e Nanotecnologias (INESC-MN)
, Rua Alves Redol, 9, 1000-029 Lisbon, Portugal
3
Instituto Superior Técnico (IST)
, Av. Rovisco Pais, 1000-029 Lisbon, Portugal
Search for other works by this author on:
P. P. Freitas
P. P. Freitas
2
Instituto de Sistemas e Computadores-Microsistemas e Nanotecnologias (INESC-MN)
, Rua Alves Redol, 9, 1000-029 Lisbon, Portugal
3
Instituto Superior Técnico (IST)
, Av. Rovisco Pais, 1000-029 Lisbon, Portugal
Search for other works by this author on:
Rev. Sci. Instrum. 83, 105113 (2012)
Article history
Received:
May 08 2012
Accepted:
October 01 2012
Citation
J. Sánchez, D. Ramírez, J. Amaral, S. Cardoso, P. P. Freitas; Electrical ammeter based on spin-valve sensor. Rev. Sci. Instrum. 1 October 2012; 83 (10): 105113. https://doi.org/10.1063/1.4759020
Download citation file:
Pay-Per-View Access
$40.00
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Citing articles via
Overview of the early campaign diagnostics for the SPARC tokamak (invited)
M. L. Reinke, I. Abramovic, et al.
An instrumentation guide to measuring thermal conductivity using frequency domain thermoreflectance (FDTR)
Dylan J. Kirsch, Joshua Martin, et al.
Design and performance of a magnetic bottle electron spectrometer for high-energy photoelectron spectroscopy
Kurtis Borne, Jordan T. O’Neal, et al.
Related Content
Enhancing electromagnetism experiments with clamp-on ammeters
Am. J. Phys. (January 2001)
Exploring a new ammeter traceability route for ionisation chamber measurements
Rev. Sci. Instrum. (January 2019)
Introductory Experiment in Electrical Measurements
American Journal of Physics (September 1957)
AC calibration procedure for resonant testing equipment
AIP Conf. Proc. (October 2023)