Skip Nav Destination
Issues
19 October 2016
In this Issue
PRELIMINARY
STRUCTURES, PROPERTIES AND PROCESSING OF POLYMERS (AND BIOMASS BASED MATERIALS)
Mechanical behaviour of glass fiber weaven UD/high fluidity PA-based polymers for automotive applications
AIP Conf. Proc. 1769, 020001 (2016)
https://doi.org/10.1063/1.4963405
Rate growth simulation of spherulitic microstructure of PET induced by the temperature using the phase field method
AIP Conf. Proc. 1769, 020002 (2016)
https://doi.org/10.1063/1.4963406
An anisotropic visco-hyperelastic model for PET behavior under ISBM process conditions
AIP Conf. Proc. 1769, 020003 (2016)
https://doi.org/10.1063/1.4963407
In-situ measurements of temperature distribution during transmission laser welding of poly(aryletherketone)
AIP Conf. Proc. 1769, 020004 (2016)
https://doi.org/10.1063/1.4963408
Wear behaviour of epoxy resin filled with hard powders
AIP Conf. Proc. 1769, 020005 (2016)
https://doi.org/10.1063/1.4963409
Higher order lubrication solutions for viscoelastic flows in converging or diverging slits
AIP Conf. Proc. 1769, 020007 (2016)
https://doi.org/10.1063/1.4963411
Multiphase and multiscale approaches for modelling the injection of textured moulds
AIP Conf. Proc. 1769, 020008 (2016)
https://doi.org/10.1063/1.4963412
Development of bio-sourced binder to metal injection moulding
AIP Conf. Proc. 1769, 020009 (2016)
https://doi.org/10.1063/1.4963413
Modeling of thermoplastic composites laser welding - A ray tracing method associated to thermal simulation
AIP Conf. Proc. 1769, 020010 (2016)
https://doi.org/10.1063/1.4963414
Infrared welding process on composite: Effect of interdiffusion at the welding interface
AIP Conf. Proc. 1769, 020011 (2016)
https://doi.org/10.1063/1.4963415
Injection blow moulding single stage process: Validation of the numerical simulation through tomography analysis
AIP Conf. Proc. 1769, 020012 (2016)
https://doi.org/10.1063/1.4963416
SEMI-SOLID PROCESSES
Material efficient production of complex (hybrid) components using semi solid forming processes
AIP Conf. Proc. 1769, 030001 (2016)
https://doi.org/10.1063/1.4963417
Thermomechanical steels behaviors at semi-solid state
AIP Conf. Proc. 1769, 030002 (2016)
https://doi.org/10.1063/1.4963418
OPTIMIZATION AND INVERSE ANALYSIS IN FORMING
Study on objective functions for the slow shot phase in high-pressure die casting
AIP Conf. Proc. 1769, 040001 (2016)
https://doi.org/10.1063/1.4963423
On the use of topology optimization for improving heat transfer in molding process
AIP Conf. Proc. 1769, 040002 (2016)
https://doi.org/10.1063/1.4963424
Experimental approach for thermal parameters estimation during glass forming process
AIP Conf. Proc. 1769, 040003 (2016)
https://doi.org/10.1063/1.4963425
Identification of microstructure evolution model on the basis of the inverse analysis of two-step compression tests
AIP Conf. Proc. 1769, 040004 (2016)
https://doi.org/10.1063/1.4963426
Design of a mechanical test to characterize sheet metals - Optimization using B-splines or cubic splines
AIP Conf. Proc. 1769, 040005 (2016)
https://doi.org/10.1063/1.4963427
A hybrid optimization approach in non-isothermal glass molding
AIP Conf. Proc. 1769, 040006 (2016)
https://doi.org/10.1063/1.4963428
NON-CONVENTIONAL PROCESSES
Experimental investigation of surface roughness in electrical discharge turning process
AIP Conf. Proc. 1769, 050001 (2016)
https://doi.org/10.1063/1.4963429
Direct molding of pavement tiles made of ground tire rubber
AIP Conf. Proc. 1769, 050002 (2016)
https://doi.org/10.1063/1.4963430
Field assisted hot pressing of sintering Inconel 718 MIM samples
AIP Conf. Proc. 1769, 050003 (2016)
https://doi.org/10.1063/1.4963431
Numerical simulation of electrified jets: An application to electrospinning
AIP Conf. Proc. 1769, 050004 (2016)
https://doi.org/10.1063/1.4963432
Press hardening of alternative high strength aluminium and ultra-high strength steels
AIP Conf. Proc. 1769, 050006 (2016)
https://doi.org/10.1063/1.4963434
Kerf generation during the plasma cutting process
Oana Dodun; Sanda Ilii Bangu; Laurenţiu Slătineanu; Merticaru Vasile; Irina Beşliu; Margareta Coteaţă
AIP Conf. Proc. 1769, 050008 (2016)
https://doi.org/10.1063/1.4963436
INTEGRATED DESIGN, MODELLING AND RELIABILITY ASSESSMENT IN FORMING
Thermo-chemical, mechanical and resin flow integrated analysis in pultrusion
AIP Conf. Proc. 1769, 060001 (2016)
https://doi.org/10.1063/1.4963437
Hard and soft computing models of composite curing process looking toward monitoring and control
AIP Conf. Proc. 1769, 060002 (2016)
https://doi.org/10.1063/1.4963438
Finite element modeling and analysis of electro-magnetic pulse welding of aluminium tubes to steel bars
AIP Conf. Proc. 1769, 060003 (2016)
https://doi.org/10.1063/1.4963439
Strain rate dependent hardening of DP600 sheet metal for large strains under in-plane biaxial loadings
AIP Conf. Proc. 1769, 060004 (2016)
https://doi.org/10.1063/1.4963440
SPIF of brass alloys: Preliminary studies
Daniel Fritzen; Gustavo S. De Lucca; Fernando M. Marques; Anderson Daleffe; Jovani Castelan; Uilian Boff; Ricardo J. Alves de Sousa; Lirio Schaeffer
AIP Conf. Proc. 1769, 060006 (2016)
https://doi.org/10.1063/1.4963442
Anisotropic mechanical behavior of an injection molded short fiber reinforced thermoplastic
AIP Conf. Proc. 1769, 060007 (2016)
https://doi.org/10.1063/1.4963443
Thermal modeling of cogging process using finite element method
AIP Conf. Proc. 1769, 060008 (2016)
https://doi.org/10.1063/1.4963444
Parallelization of fine-scale computation in Agile Multiscale Modelling Methodology
AIP Conf. Proc. 1769, 060009 (2016)
https://doi.org/10.1063/1.4963445
The effect of tooling deformation on process control in multistage metal forming
AIP Conf. Proc. 1769, 060010 (2016)
https://doi.org/10.1063/1.4963446
Numerical simulation of friction stir welding (FSW): Prediction of the heat affect zone using a softening model
AIP Conf. Proc. 1769, 060011 (2016)
https://doi.org/10.1063/1.4963447
Metamodelling with artificial neural networks by using high performance computing infrastructures
AIP Conf. Proc. 1769, 060012 (2016)
https://doi.org/10.1063/1.4963448
Two-scale modeling of joining of the aluminum alloys by a cohesive zone element technique
AIP Conf. Proc. 1769, 060013 (2016)
https://doi.org/10.1063/1.4963449
Simulations of joule effect heating in a bulge test
Nathan Demazel; Hervé Laurent; Muriel Carin; Jérémy Coër; Philippe Le Masson; Jérôme Favero; Romain Canivenc; Stéphane Graveleau
AIP Conf. Proc. 1769, 060014 (2016)
https://doi.org/10.1063/1.4963450
Prediction of the bending behavior after pre-strain of an aluminum alloy
AIP Conf. Proc. 1769, 060015 (2016)
https://doi.org/10.1063/1.4963451
Testing single point incremental forming molds for thermoforming operations
AIP Conf. Proc. 1769, 060016 (2016)
https://doi.org/10.1063/1.4963452
On the model order reduction of confined plasticity
AIP Conf. Proc. 1769, 060017 (2016)
https://doi.org/10.1063/1.4963453
INCREMENTAL AND SHEET METAL FORMING
Friction spinning – Twist phenomena and the capability of influencing them
AIP Conf. Proc. 1769, 070001 (2016)
https://doi.org/10.1063/1.4963454
Influence of part orientation on the geometric accuracy in robot-based incremental sheet metal forming
AIP Conf. Proc. 1769, 070002 (2016)
https://doi.org/10.1063/1.4963455
Simulation of sheet-bulk metal forming processes with simufact.forming using user-subroutines
Steffen Beese; Florian Beyer; Heribert Blum; Kerim Isik; Dustin Kumor; Stefan Löhnert; Andreas Rademacher; A. Erman Tekkaya; Kai Willner; Peter Wriggers; Sebastian Zeller
AIP Conf. Proc. 1769, 070004 (2016)
https://doi.org/10.1063/1.4963457
Spring-back sensitivity analysis of automotive parts according to the material parameters
AIP Conf. Proc. 1769, 070006 (2016)
https://doi.org/10.1063/1.4963459
On the use of solid–shell elements for thin structures: Application to impact and sheet metal forming simulations
AIP Conf. Proc. 1769, 070007 (2016)
https://doi.org/10.1063/1.4963460
Multiple forming tools in incremental forming – Influence of the forming strategies on sheet contour
AIP Conf. Proc. 1769, 070009 (2016)
https://doi.org/10.1063/1.4963462
Adaptive scallop height tool path generation for robot-based incremental sheet metal forming
AIP Conf. Proc. 1769, 070010 (2016)
https://doi.org/10.1063/1.4963463
High load-bearing multi-material-joints of metal sheets and composites by incremental in-situ forming processes
AIP Conf. Proc. 1769, 070011 (2016)
https://doi.org/10.1063/1.4963464
Face split interpretations in sheet metal design
AIP Conf. Proc. 1769, 070012 (2016)
https://doi.org/10.1063/1.4963465
Effects of process variation in short cycle stretch forming in beverage can production
AIP Conf. Proc. 1769, 070013 (2016)
https://doi.org/10.1063/1.4963466
The effect of cushion-ram pulsation on hot stamping
Dirk Landgrebe; Anja Rautenstrauch; Andreas Kunke; Stefan Polster; Sebastian Kriechenbauer; Reinhard Mauermann
AIP Conf. Proc. 1769, 070014 (2016)
https://doi.org/10.1063/1.4963467
Numerical and experimental analysis of cold stretching of aluminium sheets using an instrumented bench
AIP Conf. Proc. 1769, 070015 (2016)
https://doi.org/10.1063/1.4963468
Creep forming of an Al-Mg-Li alloy for aeronautic application
AIP Conf. Proc. 1769, 070016 (2016)
https://doi.org/10.1063/1.4963469
Investigations on structural thinning in deformation machining stretching mode
AIP Conf. Proc. 1769, 070017 (2016)
https://doi.org/10.1063/1.4963470
Influence of the pressure dependent coefficient of friction on deep drawing springback predictions
AIP Conf. Proc. 1769, 070018 (2016)
https://doi.org/10.1063/1.4963471
Thermomechanical simulations and experimental validation for high speed incremental forming
AIP Conf. Proc. 1769, 070019 (2016)
https://doi.org/10.1063/1.4963472
Incremental forming of aluminium alloys in cryogenic environment
AIP Conf. Proc. 1769, 070020 (2016)
https://doi.org/10.1063/1.4963473
An investigation into the mechanics of double-sided incremental forming using finite element methods
AIP Conf. Proc. 1769, 070021 (2016)
https://doi.org/10.1063/1.4963474
On the impact of rolling direction and tool orientation angle in Rotary Peen Forming
AIP Conf. Proc. 1769, 070022 (2016)
https://doi.org/10.1063/1.4963475
MACHINING AND CUTTING
Orthogonal cutting modeling of hybrid CFRP/Ti toward specific cutting energy and induced damage analyses
AIP Conf. Proc. 1769, 080001 (2016)
https://doi.org/10.1063/1.4963476
An experimental investigation on orthogonal cutting of hybrid CFRP/Ti stacks
AIP Conf. Proc. 1769, 080002 (2016)
https://doi.org/10.1063/1.4963477
Iterative Lagrangian model of broaching to study cutting forces, temperatures and chip formation
AIP Conf. Proc. 1769, 080003 (2016)
https://doi.org/10.1063/1.4963478
High productivity machining of holes in Inconel 718 with SiAlON tools
AIP Conf. Proc. 1769, 080006 (2016)
https://doi.org/10.1063/1.4963481
2D finite element model and microstructural changes during cutting of Ti6Al4V in dry condition
AIP Conf. Proc. 1769, 080010 (2016)
https://doi.org/10.1063/1.4963485
Cutting performance and wear mechanisms of PVD coated carbide tools during dry drilling of newly produced ADI
AIP Conf. Proc. 1769, 080011 (2016)
https://doi.org/10.1063/1.4963486
Effect of tool geometry and cutting parameters on delamination and thrust forces in drilling CFRP/Al-Li
AIP Conf. Proc. 1769, 080012 (2016)
https://doi.org/10.1063/1.4963487
Investigation on process parameters affecting blanking of AISI 1006 low carbon steel
AIP Conf. Proc. 1769, 080013 (2016)
https://doi.org/10.1063/1.4963488
Analysis of residual stress-induced distortions of thin sheet structures in multi-step milling
AIP Conf. Proc. 1769, 080014 (2016)
https://doi.org/10.1063/1.4963489
A new behavior model for better understanding of titanium alloys Ti-6Al-4V chip formation in orthogonal cutting
AIP Conf. Proc. 1769, 080015 (2016)
https://doi.org/10.1063/1.4963490
NANO-STRUCTURED MATERIALS AND MICRO FORMING
Modelling the deformation of nickel foil during manufacturing of nanostructures on injection moulding tool inserts
AIP Conf. Proc. 1769, 090003 (2016)
https://doi.org/10.1063/1.4963493
INNOVATIVE JOINING BY FORMING TECHNOLOGIES
Influence of FSW pin tool geometry on plastic flow of AA7075 T651
AIP Conf. Proc. 1769, 100001 (2016)
https://doi.org/10.1063/1.4963495
Fundamental studies on a novel die concept for round-point shear-clinching
AIP Conf. Proc. 1769, 100003 (2016)
https://doi.org/10.1063/1.4963497
Experimental comparison of the MIG, friction stir welding, cold metal transfer and hybrid laser-MIG processes for AA 6005-T6 aluminium alloy
Serafino Caruso; Emanuele Sgambitterra; Sergio Rinaldi; Antonello Gallone; Lucio Viscido; Luigino Filice; Domenico Umbrello
AIP Conf. Proc. 1769, 100004 (2016)
https://doi.org/10.1063/1.4963498
Dissimilar Al/steel friction stir welding lap joints for automotive applications
AIP Conf. Proc. 1769, 100005 (2016)
https://doi.org/10.1063/1.4963499
Calibration of 3D ALE finite element model from experiments on friction stir welding of lap joints
AIP Conf. Proc. 1769, 100006 (2016)
https://doi.org/10.1063/1.4963500
Formation of porous inner architecture at the interface of magnetic pulse welded Al/Cu joints
AIP Conf. Proc. 1769, 100011 (2016)
https://doi.org/10.1063/1.4963505
FEA of the clinching process of short fiber reinforced thermoplastic with an aluminum sheet using LS-DYNA
AIP Conf. Proc. 1769, 100012 (2016)
https://doi.org/10.1063/1.4963506
Effect of localized heat treatment on the weld line shift in deep drawing of tailor welded blanks (TWBs)
AIP Conf. Proc. 1769, 100015 (2016)
https://doi.org/10.1063/1.4963509
HEAT TRANSFER MODELLING
Thermo-kinetic characterization and modelling of a new generation of SMC composites
AIP Conf. Proc. 1769, 110001 (2016)
https://doi.org/10.1063/1.4963510
Two dimensional finite element thermal model of laser surface glazing for H13 tool steel
AIP Conf. Proc. 1769, 110003 (2016)
https://doi.org/10.1063/1.4963512
The improved element free Galerkin method for 2D thermo elasticity problem
AIP Conf. Proc. 1769, 110005 (2016)
https://doi.org/10.1063/1.4963514
Scattering effect in radiative heat transfer during selective laser sintering of polymers
AIP Conf. Proc. 1769, 110006 (2016)
https://doi.org/10.1063/1.4963515
FLATNESS, STRAIGHTNESS, LEVELLING, STRAIGHTENING: MEASUREMENT, MODELLING AND CONTROL
Numerical simulations of a two roll round bar straightener
AIP Conf. Proc. 1769, 120001 (2016)
https://doi.org/10.1063/1.4963516
Optimal intermeshing of multi roller cross roll straightening machine
AIP Conf. Proc. 1769, 120002 (2016)
https://doi.org/10.1063/1.4963517
A study of flatness defect in strip rolling occurred in tension unloading
AIP Conf. Proc. 1769, 120003 (2016)
https://doi.org/10.1063/1.4963518
FORGING AND ROLLING
Methodology for the analysis of the impact of the forging parameters on metallurgy and mechanical properties in case of solid electromagnetic manufactured parts
Marc Borsenberger; Cyrille Baudouin; Abdelkader Benabou; Régis Bigot; Pierre Faverolle; Jean-Claude Mipo
AIP Conf. Proc. 1769, 130002 (2016)
https://doi.org/10.1063/1.4963521
Development of strategies for saving energy by temperature reduction in warm forging processes
AIP Conf. Proc. 1769, 130003 (2016)
https://doi.org/10.1063/1.4963522
Application of multi-grid method on the simulation of incremental forging processes
AIP Conf. Proc. 1769, 130004 (2016)
https://doi.org/10.1063/1.4963523
Numerical analysis of rheological and tribological behavior influence on 16MnCr5 forging fibering
AIP Conf. Proc. 1769, 130005 (2016)
https://doi.org/10.1063/1.4963524
Idle and axial roll speed law trend effect in an industrial ring rolling process
AIP Conf. Proc. 1769, 130006 (2016)
https://doi.org/10.1063/1.4963525
Experimental study of the Portevin-Le Chatelier effect in AA 5754 sheets: Influence of the different rolling routes
AIP Conf. Proc. 1769, 130007 (2016)
https://doi.org/10.1063/1.4963526
Analytic temperature evaluation and process forces estimation for the RARR process of flat rings
AIP Conf. Proc. 1769, 130008 (2016)
https://doi.org/10.1063/1.4963527
Investigation of influencing factors on friction during ring test in hot forging using FEM simulation
AIP Conf. Proc. 1769, 130009 (2016)
https://doi.org/10.1063/1.4963528
Advanced finite element analysis of die wear in sheet-bulk metal forming processes
AIP Conf. Proc. 1769, 130010 (2016)
https://doi.org/10.1063/1.4963529
Layer texture of hot-rolled BCC metals and its significance for stress-corrosion cracking of main gas pipelines
AIP Conf. Proc. 1769, 130011 (2016)
https://doi.org/10.1063/1.4963530
Influence of die geometry and material selection on the behavior of protective die covers in closed-die forging
AIP Conf. Proc. 1769, 130012 (2016)
https://doi.org/10.1063/1.4963531
Experimental investigations on the state of the friction-welded joint zone in steel hybrid components after process-relevant thermo-mechanical loadings
B.-A. Behrens; A. Bouguecha; M. Vucetic; I. Peshekhodov; T. Matthias; N. Kolbasnikov; S. Sokolov; S. Ganin
AIP Conf. Proc. 1769, 130013 (2016)
https://doi.org/10.1063/1.4963532
Experimentation and numerical modeling of forging induced bending (FIB) process
AIP Conf. Proc. 1769, 130014 (2016)
https://doi.org/10.1063/1.4963533
Tailoring of mechanical properties of a side sill part made of martensitic stainless steel by press hardening
AIP Conf. Proc. 1769, 130015 (2016)
https://doi.org/10.1063/1.4963534
Research into oil-based high-dispersion graphite lubricants for extrusion of Ni-based alloys
AIP Conf. Proc. 1769, 130016 (2016)
https://doi.org/10.1063/1.4963535
Evaluation of undesirable deformations in complex, hollow aluminium extrusions due to roll bending
AIP Conf. Proc. 1769, 130017 (2016)
https://doi.org/10.1063/1.4963536
Realistic modelling of the tool kinematics of radial-axial ring rolling machines in finite element simulation
AIP Conf. Proc. 1769, 130018 (2016)
https://doi.org/10.1063/1.4963537
EXTRUSION AND DRAWING
Experimental determination of plastic strain in the extrusion process
AIP Conf. Proc. 1769, 140001 (2016)
https://doi.org/10.1063/1.4963538
Die swell as an objective in the design of polymer extrusion dies
AIP Conf. Proc. 1769, 140003 (2016)
https://doi.org/10.1063/1.4963540
ENERGY EFFICIENT SOLUTIONS IN MATERIAL FORMING
New process for flexible manufacturing of bent parts with variable arbitrary cross section
AIP Conf. Proc. 1769, 150001 (2016)
https://doi.org/10.1063/1.4963541
Closed-loop control concept for kinematic 3D-profile bending
AIP Conf. Proc. 1769, 150002 (2016)
https://doi.org/10.1063/1.4963542
CONSTITUTIVE MODELLING: FROM MACROSCOPIC BEHAVIOUR LAWS TO SMALL-SCALE PLASTICITY
Validation of homogeneous anisotropic hardening approach based on crystal plasticity
AIP Conf. Proc. 1769, 160001 (2016)
https://doi.org/10.1063/1.4963544
Modelling of the cellular automata space deformation within the RCAFE framework
AIP Conf. Proc. 1769, 160004 (2016)
https://doi.org/10.1063/1.4963547
Parameter estimation of rheological models for biological materials
AIP Conf. Proc. 1769, 160005 (2016)
https://doi.org/10.1063/1.4963548
Modeling of void coalescence initiation and its impact on the prediction of material failure
AIP Conf. Proc. 1769, 160006 (2016)
https://doi.org/10.1063/1.4963549
Crystal plasticity analysis of constitutive behavior of 5754 aluminum sheet
AIP Conf. Proc. 1769, 160007 (2016)
https://doi.org/10.1063/1.4963550
Non local damage model based on micromorphic formulation
AIP Conf. Proc. 1769, 160008 (2016)
https://doi.org/10.1063/1.4963551
On the control of the crystallographic texture in cladding tubes from Zr-based alloys for nuclear reactor
AIP Conf. Proc. 1769, 160009 (2016)
https://doi.org/10.1063/1.4963552
Gradient enhanced physically based plasticity: Implementation and application to a problem pertaining size effect
AIP Conf. Proc. 1769, 160011 (2016)
https://doi.org/10.1063/1.4963554
Characteristic for TNW700 high temperature titanium superplastic properties
AIP Conf. Proc. 1769, 160012 (2016)
https://doi.org/10.1063/1.4963555
COMPOSITES FORMING PROCESSES
3D modeling of squeeze flow of unidirectionally thermoplastic composite inserts
AIP Conf. Proc. 1769, 170002 (2016)
https://doi.org/10.1063/1.4963558
Viscous and thermal modelling of thermoplastic composites forming process
AIP Conf. Proc. 1769, 170003 (2016)
https://doi.org/10.1063/1.4963559
On the modeling of separation foils in thermoforming simulations
AIP Conf. Proc. 1769, 170004 (2016)
https://doi.org/10.1063/1.4963560
Prediction of tensile and flexural strength of unidirectional CFRP considering the interfacial shear strength
AIP Conf. Proc. 1769, 170005 (2016)
https://doi.org/10.1063/1.4963561
An anisotropic constitutive model with biaxial-tension coupling for woven composite reinforcements
AIP Conf. Proc. 1769, 170006 (2016)
https://doi.org/10.1063/1.4963562
Experimental investigation of fiberglass sandwich composite bending behaviour after severe aging condition
AIP Conf. Proc. 1769, 170007 (2016)
https://doi.org/10.1063/1.4963563
Experimental investigation of braided fabric forming
AIP Conf. Proc. 1769, 170009 (2016)
https://doi.org/10.1063/1.4963565
Thermo-rheological-kinetical study of compression molding of fibre-reinforced composites
AIP Conf. Proc. 1769, 170013 (2016)
https://doi.org/10.1063/1.4963569
Saturated versus non-saturated two-scales permeability
AIP Conf. Proc. 1769, 170014 (2016)
https://doi.org/10.1063/1.4963570
Analysis of large displacements/small strains of enhanced 3D beam with section changes
AIP Conf. Proc. 1769, 170015 (2016)
https://doi.org/10.1063/1.4963571
Parameter measurements of the hypo-elasticity model for dry composite reinforcement
AIP Conf. Proc. 1769, 170016 (2016)
https://doi.org/10.1063/1.4963572
Integration of heat transfer effects in simulation of composite stamping
AIP Conf. Proc. 1769, 170018 (2016)
https://doi.org/10.1063/1.4963574