The performance analysis of the evaporation cooling condenser is analyzed numerically using different approaches. One of the reliable approaches of numerical investigation is analyzed using the computation method. In computational method ANSYS FLUENT is best module to get the nearest possible solution. the different parameters like boundary condition, change in length of the tube in the heat exchanger, performance of fluid and heat flow and performance of thermal enhancement factors like variations in non-dimensional numbers and temperature distribution variances are taken into consideration. On analyzing the different parameters over different conditions, during the process of heat enhancement process Reynolds number plays a major role to increase the capability of about 9.53%. Darcy number is changing propositionally change in the Reynolds number. Because of the increased temperature in the heat flow Darcy number also increases. it indicates friction flow is increased in the flow of fluid during the process. These performances and change in parameters are easily calculate by using numerical simulation analysis techniques.
REFERENCES
1.
Yunran
Min
, Yi
Chen
, Hongxing
Yang
. 2019
. “CFD Study of Heat Transfer Enhancement and Fluid Flow Characteristics of Laminar Flow through Tube with Helical Screw Tape Insert
.” Energy Procedia
160
: 699
–706
. .2.
Wang
, Xiaoyuan
, Hao
Liu
, Yinfeng
Wang
, and Yuezhao
Zhu
. 2020
. “CFD Simulation of Dynamic Heat Transfer Behaviors in Super-Long Thermosyphons for Shallow Geothermal Application
.” Applied Thermal Engineering
174
(November 2019
): 115295
. .3.
Menni
, Younes
, Ali J
Chamkha
, Chafika
Zidani
, and Boumédiène
Benyoucef
. 2019
. “Heat Transfer in Air Flow Past a Bottom Channel Wall-Attached Diamond-Shaped Baffle – Using a CFD Technique
.” 63
(2
): 100
–112
.4.
Mehdi
Vahabzadeh
, Mohammad
Hossein
, Kun
Hong
, and Qingang
Xiong
. 2020
. “CFD Study of Heat Transfer and Fl Uid Fl Ow in a Parabolic Trough Solar Receiver with Internal Annular Porous Structure and Synthetic Oil e Al 2 O 3 Nano Fl Uid
.” Renewable Energy
145
: 2598
–2614
. .5.
Petros Demissie
Tegenaw
, Mekonnen Gebreslasie
Gebrehiwot
, and Maarten
Vanierschot
. “On the Comparison between Computational Fluid Dynamics (CFD) and Lumped Capacitance Modeling for the Simulation of Transient Heat Transfer in Solar Dryers
.”6.
Ying
Dong
, Bahne
Sosna
, Oliver
Korup
, Frank
Rosowski
and Raimund
Horn
2017
. “Investigation of Radial Heat Transfer in a Fixed-Bed Reactor:CFD Simulations and Profile Measurements
.” Chemical Engineering Journal.
.7.
Khashayar
Sharifi
, Morteza
Sabeti
, Mehdi
Rafiei
, Amir H.
Mohammadi
and Laleh
Shirazi
2017
. “Computational Fluid Dynamics (CFD) Technique to Study the Effects of Helical Wire Inserts on Heat Transfer and Pressure Drop in a Double Pipe Heat Exchanger
.” Applied Thermal Engineering.
.8.
Yavar
Karimi
, Ali Reza Solaimany
Nazar
and Mohsen
Motevasel
2020
. “CFD simulation of nanofluid heat transfer considering the aggregation of nanoparticles in population balance model
”. Journal of Thermal Analysis and Calorimetry.
9.
Lichtenegger
T.
, E. A. J. F.
Peters
, J. A. M.
Kuipers
and S.
Pirker
. 2017
. “A Recurrence CFD Study of Heat Transfer in a Fluidized Bed
.”. Chemical Engineering Science.
10.
Minglu
Wanga
, Mingguang
Zheng
, Mengke
Chao
, Jianhui
Yu
, Xingliang
Zhang
and Lin
Tian
2019
. “Progress in Nuclear Energy Experimental and CFD Estimation of Single-Phase Heat Transfer in Helically Coiled Tubes
.” Progress in Nuclear Energy
112
(29
): 185
–90
. .11.
Turo
Välikangas
, Mikko
Folkersma
, Miikka
Dal Maso
, Tuomo
Keskitalo
, Petteri
Peltonen
and Ville
Vuorinen
2022
. “Parametric CFD Study for Finding the Optimal Tube Arrangement of a Fin-and-Tube Heat Exchanger with Plain Fins in a Marine Environment
.” Applied Thermal Engineering
200
(May 2021
): 117642
. .12.
Zhimin
Zhenga
, Wenming
Yanga
, Peng
Yu
, Yongtie
Caia
, Hao
Zhou
, Siah Keng
Boon
and Prabakaran
Subbaiah
2020
. “Simulating Growth of Ash Deposit in Boiler Heat Exchanger Tube Based on CFD Dynamic Mesh Technique
.” Fuel
259
(February 2018
): 116083
. .13.
Nihat
Bicer
, Tahsin
Engin
, Halit
Yasar
, Ekrem
Büyükkaya
, Ahmet
Aydın
and Adnan
Topuz
2020
. “International Journal of Thermal Sciences Design Optimization of a Shell-and-Tube Heat Exchanger with Novel Three-Zonal Baffle by Using CFD and Taguchi Method
.” 155
(March).14.
Ildar
Akhmadullinand
and Alexander
Kartushinsky
2021
. “CFD Simulation of Bubbly Flow in a Long Coaxial Heat Exchanger
.” Thermal Science and Engineering Progress
25
(January): 100991
. .15.
D.M.
Aliaga
, R.
Feick
, W.K.
Brooks
, M.
Mery
, R.
Gers
, J.F.
Levi
and C.P.
Romero
2021
. “Modified Solar Chimney Configuration with a Heat Exchanger: Experiment and CFD Simulation
.” Thermal Science and Engineering Progress
22
(January): 100850
. .16.
Miftah
Altwieb
, Krzysztof J.
Kubiak
, Aliyu M.
Aliyu
and Rakesh
Mishra
. 2020
. “A New Three-Dimensional CFD Model for efficiency Optimisation of Fluid-to-Air Multi-Fi n Heat Exchanger
.” Thermal Science and Engineering Progress
19
(July): 100658
. .17.
Ahmed M. Nagib
Elmekawy
, Alaa A.
Ibrahim
, Abdalrahman M.
Shahin
, Sara
Al-Ali
, Gasser E.
Hassan
2021
. “Chemical Engineering and Processing - Process Intensification Performance Enhancement for Tube Bank Staggered Configuration Heat Exchanger – CFD Study
.” Chemical Engineering and Processing - Process Intensification
164
(March): 108392
. .18.
Poornodaya Venkata Krishna Varma
Kola
, Srinivas Kishore
Pisipaty
, Siva Subrahmanyam
Mendu
and Rajesh
Ghosh
2021
. “Chemical Engineering and Processing - Process Intensification Optimization of Performance Parameters of a Double Pipe Heat Exchanger with Cut Twisted Tapes Using CFD and RSM
.” Chemical Engineering and Processing - Process Intensification
163
(January): 108362
. .19.
Mohammad
Pourhoseinian
, Neda
Asasian-kolur
and Seyedmehdi
Sharifian
. 2021
. “CFD Investigation of Heat and Moisture Recovery from Air with Membrane Heat Exchanger
.” Applied Thermal Engineering
191
(November 2020): 116911
. .20.
Dapeng
Yanga
, Tariq S.
Khanb
, Ebrahim
Al-Hajri
, Zahid H.
Ayub
and Adnan H.
Ayub
2019
. “Geometric Optimization of Shell and Tube Heat Exchanger with Interstitial Twisted Tapes Outside the Tubes Applying CFD Techniques
.” Applied Thermal Engineering
152
(February): 559
–72
. .21.
Jun-de
Li
2013
. “International Journal of Heat and Mass Transfer CFD Simulation of Water Vapour Condensation in the Presence of Non-Condensable Gas in Vertical Cylindrical Condensers
.” International Journal of Heat and Mass Transfer
57
(2
): 708
–21
. .22.
Wenguang
Li
, Guopeng
Yu
, Daniele
Zagaglia
, Richard
Green
and Zhibin
Yu
2020
. “Geothermics CFD Modelling of a Thermal Chimney for Air-Cooled Condenser
.” Geothermics
88
(June): 101908
. .23.
Rämä
, T.
, T.
Toppila
, D. C.
Visser
and N. B.
Siccama
. 2019
. “Validation of Ice Condenser Model for CFD Analysis of VVER-440 Type Containment
.” Nuclear Engineering and Design
352
(June): 110163
. .24.
Heecheon
Lee
, Chaeyeong
Seo
, Minyong
Lee
and Jae W.
Lee
, 2021
. “CFD-Aided Design of Internally Heat-Integrated Pressure-Swing Distillation for Ternary Azeotropic Separation Constrained by Pinch Pressure
.” Applied Thermal Engineering
195
(January): 117198
. .25.
Nitin
Minocha
, Jyeshtharaj B.
Joshi
, Arun K.
Nayak
and Pallippattu K.
Vijayan
. 2016
. “3D CFD Simulations to Study the Effect of Inclination of Condenser Tube on Natural Convection and Thermal Stratification in a Passive Decay Heat Removal System
.” Nuclear Engineering and Design
305
: 582
–603
. .26.
Nuria
Regalado-rodríguez
, and Carmelo
Militello
. 2022
. “Comparative Study of the Effects of Increasing Heat Transfer Area within Compression and Expansion Chambers in Combination with Modified Pistons in Stirling Engines. A Simulation Approach Based on CFD and a Numerical Thermodynamic Model
.” Energy Conversion and Management
268
(July): 115930
. .27.
R.
Jeyakumar
, P. S.
Sampath
, R.
Ramamoorthi
, and T.
Ramakrishnan
, “Structural, morphological and mechanical behaviour of glass fibre reinforced epoxy nanoclay composites
,” Int. J. Adv. Manuf. Technol.
, vol. 93
, no. 1–4
, pp. 527
–535
, 2017
, doi: .28.
T.
Ramakrishnan
and P. S.
Sampath
, “Dry sliding wear characteristics of new short agave angustifolia marginata (AAM) fiber-reinforced polymer matrix composite material
,” J. Biobased Materials Bioenergy
, vol. 11
, no. 5
, pp. 391
–399
, 2017
, doi: .29.
R.
Thirumalaisamy
and S. Pavayee
Subramani
, “Investigation of physico-mechanical and moisture absorption characteristics of raw and alkali treated new agave angustifolia marginata (AAM) fiberies and moisture absorption of raw and alkali treated new agave angustifolia marginata (AAM) plant fiber
,” Mater. Sci.
, vol. 24
, no. 1
, pp. 53
–58
, 2018
, doi: .30.
Xinyu
Zhang
, Yunting
Ge
, Jining
Sun
and Savvas A.
Tassou
2019
. “CFD Modelling of Finned-tube CO2 Gas Cooler for Refrigeration Systems
” Energy Procedia
161
: 275
–82
. .31.
T.
Ramakrishnan
et al, “Study of various epoxy-based surface coating techniques for anticorrosion properties
,” Adv. Mater. Sci. Eng.
, vol. 2022
, pp. 1
–8
, 2022
, doi: .32.
T.
Ramakrishnan
et al, “Effect of moisture content on mechanical properties of AAM natural fiber- reinforced isophthalic polyester composites
,” Adv. Mater. Sci. Eng.
, vol. 2022
, pp. 1
–10
, 2022
, doi: .33.
T.
Ramakrishnan
et al, “Study of numerous resins used in polymer matrix composite materials
,” Adv. Mater. Sci. Eng.
, vol. 2022
, pp. 1
–8
, 2022
, doi: .34.
Saravanan
, D.
, Gokilakrishnan
, G.
, & Raajeshkrishna
, C. R.
(2021
). Effect of carbon/kevlar reinforcement and hybrid order on mechanical properties of glass/epoxy composites
. Advances in Materials and Processing Technologies
, 1
–12
.35.
Satishkumar
, P.
, Krishnan
, G. G.
, Seenivasan
, S.
, & Rajarathnam
, P.
(2021
). A study on tribological evaluation of hybrid aluminium metal matrix for thermal application
. Materials Today: Proceedings.
36.
Engin
Söylemez
, Emre
Alpman
, Ayhan
Onat
and Yalçin
Yükselentürk
. 2019
. “Numerical (CFD) and Experimental Analysis of Hybrid Household Refrigerator Including Thermoelectric and Vapour Compression Cooling Systems
” 99
: 300
–315
.37.
Murugesan
, V.
, Varthanan
, P. A.
, Murugan
, S. S.
, & Gokilakrishnan
, G.
(2022
). Numerical Analysis of the Effect of Heat Input in the Spot Welding Of Dissimilar Materials
. Materials and Technology
, 56
(3
), 307
–313
.38.
Gokilakrishnan
, G.
, Sathishkumar
, R.
, Sivakumar
, N. S.
, Kaliappan
, S.
, Sekar
, S.
, Patil
, P. P.
, … & Tadesse
, F. W.
(2022
). Wear Behavior and FESEM Analysis of LM 25 Alloy MMHCs Reinforced with FE3O4 and Gr by Utilizing Taguchi’s Technique
. Journal of Nanomaterials
, 2022
.39.
Thiyagu
, T. T.
, Gokilakrishnan
, G.
, Uvaraja
, V. C.
, Maridurai
, T.
, & Prakash
, V. R.
(2022
). Effect of SiO2/TiO2 and ZnO nanoparticle on cardanol oil compatibilized PLA/PBAT bio composite packaging film
. Silicon
, 14
(7
), 3795
–3808
.40.
Gopal
, G.
, & Murugesan
, V.
(2022
). Comparative assessment over the selection of lean supply chain practices through fuzzy integrated principal component analysis, gray relational analysis, and complex proportional assessment approaches
. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
, 09544089221103505
.41.
Abdalazeem
Adam
, Dong
Han
, Weifeng
He
and Majid
Amidpour
. 2021
. “International Journal of Heat and Mass Transfer Analysis of Indirect Evaporative Cooler Performance under Various Heat and Mass Exchanger Dimensions and Flow Parameters
.” International Journal of Heat and Mass Transfer
176
: 121299
. .42.
V.
Naveenprabhu
& M.
Suresh
(2022
) Performance assessment of annular fins and cellulose cooling pad on heat transfer enhancement of evaporative heat exchangers using volumetric heat and mass transfer coefficients
, Numerical Heat Transfer, Part A: Applications
, 83
, 504
–523
, 43.
V.
Naveenprabhu
& M.
Suresh
(2020
) Performance enhancement studies on evaporative cooling using volumetric heat and mass transfer coefficients
, Numerical Heat Transfer, Part A: Applications
, 78
:9
, 504
–523
, DOI: 44.
Dhiraviam
, F. J.
, Naveenprabhu
, V.
, Satish
, K.
, & Palanivelrajan
, A. R.
(2019
). Emission characteristic in CI engines using zirconium porous medium in piston head
. Renewable Energy Sources and Technologies
, 2161
(1
), 020012
. DOI: 45.
V.
Naveenprabhu
and M.
Suresh
, “Performance evaluation of tube-in-tube heat exchanger using nanofluids
”, Applied Mechanics and Materials
, Vol 787
(2015
), pp. 72
–76
. DOI:46.
Y.
Sureshbabu
, P.
Ashokavarthnan
, S.
Balasubramani
, and V.
Naveenprabhu
, Experimental investigation on four strokes catalytic coated spark ignition (SI) engine
, AIP Conference Proceedings
2161
, 020041
(2019
); 47.
Naveen
Prabhu
, V., K.
SaravanaKumar
, T.
Suresh
, and M.
Suresh
. "Experimental investigation on tube-in- tube heat exchanger using nanofluids
." Advances in Natural and Applied Sciences
10
, no. 7
SE (2016
): 272
.48.
Naveenprabhu
, V.
, Dhiraviam
, F. J.
, Gowtham
, K. M.
, Gowtham
, S.
, Tharick
, R. A.
, & Arunkumar
, R.
(2019
). Smart Hot Chamber in Refrigeration System Based on Waste Heat Recovery
. Indian Journal of Science and Technology
, 12
, 20
49.
Yunran
Min
, Yi
Chen
and Hongxing
Yang
. 2019
. “International Journal of Heat and Mass Transfer Numerical Study on Indirect Evaporative Coolers Considering Condensation: A Thorough Comparison between Cross Flow and Counter Flow
.” International Journal of Heat and Mass Transfer
131
: 472
–86
. .50.
Venkatesh
, S.
, Sakthivel
, M.
, Sudhagar
, S.
, & Daniel
, S. A. A.
(2018
). Modification of the cyclone separator geometry for improving the performance using Taguchi and CFD approach
. Particulate Science and Technology
, 37
(7
), 799
–808
.51.
Venkatesh
, S.
, Sakthivel
, M.
, Saranav
, H.
, Saravanan
, N.
, Rathnakumar
, M.
, & Santhosh
, K. K.
(2020
). Performance investigation of the combined series and parallel arrangement cyclone separator using experimental and CFD approach
. Powder Technology
, 361
, 1070
–1080
.52.
Venkatesh
, S.
, Sivapirakasam
, S. P.
, Sakthivel
, M.
, Ganeshkumar
, S.
, Prabhu
, M. M.
, & Naveenkumar
, M.
(2021
). Experimental and numerical investigation in the series arrangement square cyclone separator
. Powder Technology
, 383
, 93
–103
.53.
Venkatesh
, S.
, Sakthivel
, M.
, Avinasilingam
, M.
, Gopalsamy
, S.
, Arulkumar
, E.
, & Devarajan
, H. P.
(2019
). Optimization and experimental investigation in bottom inlet cyclone separator for performance analysis
. Korean Journal of Chemical Engineering
, 36
(6
), 929
–941
.
This content is only available via PDF.
©2023 Authors. Published by AIP Publishing.
2023
Author(s)
You do not currently have access to this content.
