To see the flow pattern that occurs in the Pelton turbine blade mold, it is seen by comparing the pressure drop and the comparison of the pressure drop with the speed using Solidworks software. The moving fluid makes the propeller rotate and produces energy to move the rotor. The research was conducted to see the process of resin pouring in the Pelton turbine blade mold using Solidworks software. From the simulation results, the velocity value is 0.0003 m/s, the pressure drop is 35495.65 Pa at 0.000475 m/s velocity pressure drop =52012.65 Pa and 0.00065 m/s =77152.41 Pa at velocity 0.00825 m/s obtained pressure drip =115700.58 Pa. the velocity value with the pressure drop value is directly proportional, that is, if the velocity value is greater, the pressure value is also greater and the comparison value between pressure drop with the incoming velocity value from the Z-axis (vertical) is also directly proportional. The appropriate speed for numerical analysis using Solidworks software is 0.0003 m/s.

1.
S.
Alimirzazadeh
,
T.
Kumashiro
,
S.
Leguizamon
,
E.
Jahanbakhsh
,
A.
Maertens
,
C.
Vessaz
,
K.
Tani
, and
F.
Avellan
,
Energy
148
234
(
2020
).
2.
Y.
Matsuo
,
A.
Yanagisawa
, and
Y.
Yamashita
,
Rev
2
,
79
(
2013
).
3.
C.
Chen
,
Y.
Jiang
,
Z.
Ye
,
Y.
Yang
, and
L.
Hou
,
Energy Interconnect
2
,
98
(
2019
).
4.
А. И.
Аптекарев
,
A. I.
Aptekarev
,
Д. Н.
Туляков
, and
D. N.
Tulyakov
,
5
,
177
(
2015
).
5.
M. A.
Siregar
and
W. S.
Damanik
,
Ser. Mater. Sci. Eng
821
1
(
2020
).
6.
W. S.
Damanik
,
F. H.
Napitupulu
,
A. H.
Nasution
, and
H.
Ambarita
,
Ser. Mater. Sci. Eng
725
1
(
2020
).
7.
H.
Yang
and
L.
Lee
.
J, Appl. Polym. Sci
84
,
211
(
2002
).
8.
N.
Kiuna
,
C. J.
Lawrence
,
Q. P. V.
Fontana
,
P. D.
Lee
,
T.
Selerland
, and
P. D. M.
Spelt
,
Part A Appl. Sci. Manuf
33
,
1497
(
2002
).
9.
10.
M. A.
Siregar
,
K.
Umurani
, and
W. S.
Damanik
,
Tek. Mesin
21
,
57
(
2020
).
11.
K.
Rissanen
,
T.
Holtta
,
A.
Vanhatalo
,
J.
Aalto
,
E.
Nikinmaa
,
H.
Rita
, and
J.
Back
,
Cell Environ.
39
,
527
(
2016
).
12.
E.
Jahanbakhsh
,
C.
Vessaz
,
A.
Maertens
, and
F.
Avellan
,
Methods Appl. Mech. Eng
298
80
(
2016
).
13.
A. K.
Rai
,
A.
Kumar
, and
T.
Staubli
,
Energy
145
893
(
2020
).
14.
A. K.
Rai
,
A.
Kumar
, and
T.
Staubli
, in
Pap. Curr. Res
(
2018
).
15.
U.
Dorji
and
R.
Ghomashchi
,
Fail. Anal
44
,
136
(
2014
).
16.
B. S.
Thapa
,
O. G.
Dahlhaug
, and
B.
Thapa
,
Sustain. Energy Rev
49
1100
(
2015
).
17.
B.
Suyesh
,
V.
Parag
,
D.
Keshav
,
A. M.
Ahmed
, and
O.
Abdul-Ghani
,
Sustain. Energy Rev
112
,
87
(
2019
).
18.
A.
Perrig
,
F.
Avellan
,
J. L.
Keuny
,
M.
Farhat
, and
E.
Parkinson
,
J. Fluids Eng. Trans. ASME
128
,
350
(
2006
).
19.
S.
Lubis
,
C. A.
Siregar
, and
F.
Abdilah
,
Ser. Mater. Sci. Eng
821
, (
2020
).
20.
R.
Petela
,
Energy
74
,
469
(
2003
).
21.
L.
Sahota
,
Shyam
, and
G. N.
Tiwari
,
Manag
135
308
(
2017
).
This content is only available via PDF.
You do not currently have access to this content.