The effect of different reinforcement material on mechanical and tribological properties of composite friction brake was studied. This paper aims to investigate the effect of rockwool and glass fiber on specific wear rate, friction coefficient, and flexural strength of composite. Composite specimens were manufactured utilizing a sequential processing as follows: mixing of composite ingredients, cold pressing of the mixture, hot pressing of the preformed specimen, and then post curing of the hot molded specimen. Hot press was carried out under a pressure of 20 MPa at 160 °C. Friction characteristics of composite were measured using pin on disc tribometer. Three-point bending test was carried out to obtain composite flexural strength. The results showed that rockwool had a higher effect on increasing coefficient of friction, specific wear and flexural strength of composite compared to glass fiber. Fiber fracture, fiber pull-out and void were found on the fracture surface of the bending test specimens.
Skip Nav Destination
Article navigation
30 November 2022
2021 2ND INTERNATIONAL CONFERENCE ON INFORMATION TECHNOLOGY, ADVANCED MECHANICAL AND ELECTRICAL ENGINEERING (ICITAMEE)
25–26 August 2021
Yogyakarta, Indonesia
Research Article|
November 30 2022
Effect of different reinforcement material on characteristics of composite friction brake
Eko Surojo;
Eko Surojo
a)
1)
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret
, Surakarta, Indonesia
57126a)Corresponding author: esurojo@ft.uns.ac.id
Search for other works by this author on:
Alfian Insani Fadil;
Alfian Insani Fadil
b)
1)
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret
, Surakarta, Indonesia
57126
Search for other works by this author on:
Dody Ariawan;
Dody Ariawan
c)
1)
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret
, Surakarta, Indonesia
57126
Search for other works by this author on:
Nurul Muhayat;
Nurul Muhayat
d)
1)
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret
, Surakarta, Indonesia
57126
Search for other works by this author on:
Wijang Wisnu Raharjo;
Wijang Wisnu Raharjo
e)
1)
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret
, Surakarta, Indonesia
57126
Search for other works by this author on:
Dharu Feby Smarandhana
Dharu Feby Smarandhana
f)
1)
Department of Mechanical Engineering, Faculty of Engineering, Universitas Sebelas Maret
, Surakarta, Indonesia
57126
Search for other works by this author on:
AIP Conf. Proc. 2499, 040018 (2022)
Citation
Eko Surojo, Alfian Insani Fadil, Dody Ariawan, Nurul Muhayat, Wijang Wisnu Raharjo, Dharu Feby Smarandhana; Effect of different reinforcement material on characteristics of composite friction brake. AIP Conf. Proc. 30 November 2022; 2499 (1): 040018. https://doi.org/10.1063/5.0104977
Download citation file:
Sign in
Don't already have an account? Register
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Pay-Per-View Access
$40.00
34
Views
Citing articles via
Design of a 100 MW solar power plant on wetland in Bangladesh
Apu Kowsar, Sumon Chandra Debnath, et al.
Inkjet- and flextrail-printing of silicon polymer-based inks for local passivating contacts
Zohreh Kiaee, Andreas Lösel, et al.
Production and characterization of corncob biochar for agricultural use
Praphatsorn Rattanaphaiboon, Nigran Homdoung, et al.
Related Content
Study of wear resistance for epoxy reinforced with rockwool and nanoclay
AIP Conference Proceedings (November 2021)
Friction characteristics of hybrid composite brake block reinforced by cantala fiber, glass fiber and rockwool
AIP Conference Proceedings (March 2022)
Reactive acoustic liner design
J Acoust Soc Am (September 2018)
Influence of alkaline treatment of cantala fiber on flexural strength of composite friction brake
AIP Conference Proceedings (November 2022)
An alternative Biot's formulation for dissipative porous media with skeleton deformation
J. Acoust. Soc. Am. (December 2013)