Electrical energy produced by photovoltaic technology varies depending on the intensity of sunlight, so we need a treatment to regulate it. There are 2 methods used to operate solar panels at their maximum power point, namely the dynamic method and the static method. One static method is the MPPT method with constant voltage. Boost converter and microcontroller are used to set the algorithm. The use of a boost converter to increase the working voltage of the PV to suit the needs of the load is used. Lead-acid batteries have a certain temperature sensitivity. Voltage output settings are set using the duty cycle, to obtain a stable charging voltage. By testing of charging a 24V 36 Ah battery for 12 hours. With an average charging current of 0.3 A, it is able to charge from 22.16 V to 23.23 V or increases of 1.07 V using open controls. In closed temperature control over voltage, the charging current averages 0.3 A, the battery SoC increases from 22.23 V to 23.27 V or increase of 1.05 Volts. In each test, the battery SoC increases by 1 V or 4% of the battery capacity. The effect of battery charging temperature on this study was small, both in closed control and open control. The increase in temperature between open control and closed control is about 1-2,5 °C and the increase does not touch the maximum limit value of 35 °C
Skip Nav Destination
Article navigation
13 April 2020
THE 5TH INTERNATIONAL CONFERENCE ON INDUSTRIAL, MECHANICAL, ELECTRICAL, AND CHEMICAL ENGINEERING 2019 (ICIMECE 2019)
17–18 September 2019
Surakarta, Indonesia
Research Article|
April 13 2020
Design and implementation of closed-loop controls for smart charging lithium ion battery UNS using switching technique boost converter
Chico Hermanu Brillianto Apribowo;
Chico Hermanu Brillianto Apribowo
a)
1
Department of Electrical Engineering, Faculty of Engineering, Sebelas Maret University
, Jl. Ir. Sutami 36 A, Surakarta, Central Java, Indonesia
571262
National Center for Sustainable Transportation Technology
Bandung, Indonesia
a)Corresponding author: [email protected]
Search for other works by this author on:
Muhammad Akmal;
Muhammad Akmal
b)
1
Department of Electrical Engineering, Faculty of Engineering, Sebelas Maret University
, Jl. Ir. Sutami 36 A, Surakarta, Central Java, Indonesia
57126
Search for other works by this author on:
Miftahul Anwar
Miftahul Anwar
c)
1
Department of Electrical Engineering, Faculty of Engineering, Sebelas Maret University
, Jl. Ir. Sutami 36 A, Surakarta, Central Java, Indonesia
57126
Search for other works by this author on:
AIP Conf. Proc. 2217, 030192 (2020)
Citation
Chico Hermanu Brillianto Apribowo, Muhammad Akmal, Miftahul Anwar; Design and implementation of closed-loop controls for smart charging lithium ion battery UNS using switching technique boost converter. AIP Conf. Proc. 13 April 2020; 2217 (1): 030192. https://doi.org/10.1063/5.0000830
Download citation file:
Pay-Per-View Access
$40.00
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
26
Views
Citing articles via
Inkjet- and flextrail-printing of silicon polymer-based inks for local passivating contacts
Zohreh Kiaee, Andreas Lösel, et al.
Design of a 100 MW solar power plant on wetland in Bangladesh
Apu Kowsar, Sumon Chandra Debnath, et al.
Effect of coupling agent type on the self-cleaning and anti-reflective behaviour of advance nanocoating for PV panels application
Taha Tareq Mohammed, Hadia Kadhim Judran, et al.