In this work we focus on characterization of LC200N steel by back-scattering Mössbauer spectrometry (MS). This geometry was used due to high sample thickness (0.5 mm). MS is a method suitable for determination of iron compounds and their properties in steels. We investigated samples with three different thermal treatments: non-hardened, hardened, and hardened with subsequent rapid quenching. Disk-shaped samples were cut off from original rods and polished from one side. The effect of surface treatment was investigated, too. Variations in microstructure imposed by different thermal and surface treatments were unveiled by Mössbauer parameters of backscattering spectra taken from both sides of the investigated samples. In this way, differences between the original as-cut and polished surfaces of the disks were unveiled.
Skip Nav Destination
Article navigation
27 October 2016
MÖSSBAUER SPECTROSCOPY IN MATERIALS SCIENCE 2016
23–27 May 2016
Liptovský Ján, Slovakia
Research Article|
October 27 2016
Investigation of corrosion-resistant LC200N steel by back scattering Mössbauer spectrometry
Lukáš Pašteka;
Lukáš Pašteka
a)
1Institute of Laboratory Research on Geomaterials, Faculty of Natural Sciences,
Comenius University in Bratislava
, Ilkovičova 6, 842 15 Bratislava, Slovakia
Search for other works by this author on:
Marcel Miglierini;
Marcel Miglierini
b)
2
Slovak University of Technology in Bratislava
, Faculty of Electrical Engineering and Information Technology, Institute of Nuclear and Physical Engineering, Ilkovičova 3, 812 19 Bratislava, Slovakia
3Department of Nuclear Reactors, Faculty of Nuclear Science and Physical Engineering,
Czech Technical University in Prague
, V Holešovičkách 2, 180 00 Prague 8, Czech Republic
Search for other works by this author on:
Július Dekan;
Július Dekan
c)
2
Slovak University of Technology in Bratislava
, Faculty of Electrical Engineering and Information Technology, Institute of Nuclear and Physical Engineering, Ilkovičova 3, 812 19 Bratislava, Slovakia
Search for other works by this author on:
Milan Štefánik
Milan Štefánik
d)
3Department of Nuclear Reactors, Faculty of Nuclear Science and Physical Engineering,
Czech Technical University in Prague
, V Holešovičkách 2, 180 00 Prague 8, Czech Republic
Search for other works by this author on:
a)
Corresponding authors: pashty89@gmail.com
AIP Conf. Proc. 1781, 020018 (2016)
Citation
Lukáš Pašteka, Marcel Miglierini, Július Dekan, Milan Štefánik; Investigation of corrosion-resistant LC200N steel by back scattering Mössbauer spectrometry. AIP Conf. Proc. 27 October 2016; 1781 (1): 020018. https://doi.org/10.1063/1.4966014
Download citation file:
Sign in
Don't already have an account? Register
Sign In
You could not be signed in. Please check your credentials and make sure you have an active account and try again.
Pay-Per-View Access
$40.00
20
Views
Citing articles via
The effect of a balanced diet on improving the quality of life in malignant neoplasms
Yu. N. Melikova, A. S. Kuryndina, et al.
Animal intrusion detection system using Mask RCNN
C. Vijayakumaran, Dakshata, et al.
Recognition of cat ras of face and body using convolutional neural networks
Akhmad Wahyu Aji, Esmeralda Contessa Djamal, et al.
Related Content
Mössbauer spectrometry of LC 200N steel
AIP Conference Proceedings (October 2016)
Iron meteorite fragment studied by atomic and nuclear analytical methods
AIP Conference Proceedings (October 2016)
Development of tri-sandwich Cu-Ni-Cr coating over weathering steel used for construction applications
AIP Conference Proceedings (December 2020)
Protein sequence analysis of the Zika virus and the dengue virus using Smith Waterman algorithm
AIP Conf. Proc. (March 2019)
Studies on the work characteristics of amperometric free chlorine probes
AIP Conf. Proc. (October 2018)